fixed formatting

1 files changed, 33 insertions, 33 deletions

diff --git a/README.md b/README.md
index 64ff9ca..5db9089 100644
--- a/README.md
+++ b/README.md
@@ -1,52 +1,52 @@
 # Linux kernel module for the Thrustmaster T300RS wheel
 
 ## Current state
+Playable. Dynamic updating of effects isn't baked into the wheel quite as
+well as I'd hoped, and so the driver in its current state doesn't really
+support it. At some point in the future I'd like to add it to the feature
+list, but it will need a lot more research and might take a while.
 
-    Playable. Dynamic updating of effects isn't baked into the wheel quite as
-    well as I'd hoped, and so the driver in its current state doesn't really
-    support it. At some point in the future I'd like to add it to the feature
-    list, but it will need a lot more research and might take a while.
+One other issue is that if you have the T3PA pedals, the clutch doesn't seem
+to be registered by most(all?) games. It is registered and works as expected
+in jstest and jstest-gtk, no clue what that is about.
 
-    One other issue is that if you have the T3PA pedals, the clutch doesn't seem
-    to be registered by most(all?) games. It is registered and works as expected
-    in jstest and jstest-gtk, no clue what that is about.
-
-    Anycase, *this version is usable in most force feedback games, supports
-    rangesetting as well as gain and autocentering along with most force feedback effects.**
+Anycase, **this version is usable in most force feedback games, supports
+rangesetting as well as gain and autocentering along with most force feedback effects.**
 ## Small note
     
-    While I haven't personally come across any crashes or lockups with this
-    version, I can't promise that they won't occur under any circumstances.
+While I haven't personally come across any crashes or lockups with this
+version, I can't promise that they won't occur under any circumstances.
 
-    With that in mind,
+With that in mind,
 
 ## Installation
 
-    + Unplug wheel from computer
-    + `git clone this-repo`
-    + `make`
-    + `sudo make install`
-    + Plug wheel back in
-    + reboot (not strictly necessary, but recommended)
++ Unplug wheel from computer
++ `git clone this-repo`
++ `make`
++ `sudo make install`
++ Plug wheel back in
++ reboot (not strictly necessary, but recommended)
     
-    Done!
+Done!
 
 ## Additional tidbits
     
-    + Change range:
-        
-        Write a value between 0 and 65535 to
-        /sys/bus/devices/XXXX:044F:B66E.XXX/range
++ Change range:
+  
+Write a value between 0 and 65535 to
+/sys/bus/devices/XXXX:044F:B66E.XXX/range
 
-    + Change autocenter and gain:
++ Change autocenter and gain:
 
-        Use the default evdev ways, i.e. https://www.kernel.org/doc/html/v5.1/input/ff.html
+Use the default evdev ways, i.e. https://www.kernel.org/doc/html/v5.1/input/ff.html
     
-    + Currently there is no support for this driver in oversteer(https://github.com/berarma/oversteer), but ffbwrap(https://github.com/berarma/ffbtools) should work.
-    + If the wheel has a deadzone in games, you can set up a udev rule:
-        `/etc/udev/rules.d/99-joydev.rules`:
-        `SUBSYSTEM=="input", ATTRS{idVendor}=="044f", ATTRS{idProduct}=="b66e"
++ Currently there is no support for this driver in oversteer(https://github.com/berarma/oversteer), but ffbwrap(https://github.com/berarma/ffbtools) should work.
++ If the wheel has a deadzone in games, you can set up a udev rule:
+    /etc/udev/rules.d/99-joydev.rules
+
+    SUBSYSTEM=="input", ATTRS{idVendor}=="044f", ATTRS{idProduct}=="b66e"
+    RUN+="/usr/bin/evdev-joystick --evdev %E{DEVNAME} --deadzone 0"
 
-        RUN+="/usr/bin/evdev-joystick --evdev %E{DEVNAME} --deadzone 0"`
-        This should make sure that the wheel behaves like you'd want from a
-        wheel.
+This should make sure that the wheel behaves like you'd want from a
+wheel.